3M IEC C7 Figure of 8 Eight Mains Power Cable Lead - 3 Metre Long (Black)

Product Information

Very common on personal computers and peripherals. Commonly referred to as a "kettle cord" or "kettle lead", [17] [18] but kettles in countries using 120V require the C15/C16. Interconnection cord set: "assembly consisting of one cable or cord fitted with one non-rewirable plug connector and one non-rewirable connector, intended for the interconnection between two electrical appliances". Appliance outlet: "part of the interconnection coupler which is the part integrated or incorporated in the appliance or equipment or intended to be fixed to it and from which the supply is obtained".

International Standardized Appliance Connectors (IEC-60320) Reference Chart Includes diagrams of all couplers, their rated current, equipment class, and temperature rating. A similar but polarized connector has been made, but is not part of the standard. Sometimes called C7P, it is asymmetrical, with one side squared. Unpolarized C7 connectors can be inserted into the polarized inlets; however, doing so might be a safety risk if the device is designed for polarized power. Although not specified by IEC 60320, and not clear whether any formal written standard exists, the most common wiring appears to connect the squared side to the neutral, and the rounded to the hot line. [23] [24] Note: Clause 9.5 was added to IEC 60320-1:2015, this requires that "It shall not be possible to engage a part of a non-standard appliance coupler with a complementary part of an appliance coupler complying with the standard sheets in any part of IEC 60320." IEC 60320-1: General Requirements [1] specifies two- pole and two-pole with earth couplers intended for the connection of a mains supply cord to electrical appliances. Beginning with the IEC 60320-1:2015 edition, [5] this part also specifies interconnection couplers which enable the connection and disconnection of an appliance to a cord leading to another appliance, incorporating IEC 60320-2-2. At the same time, this part of the standard no longer includes standard sheets which were moved to a new part: IEC 60320-3. IEC 60320-1 defines a cord set as an "assembly consisting of one cable or cord fitted with one plug and one connector, intended for the connection of an electrical appliance or equipment to the electrical supply". It also defines an interconnection cord set as an "assembly consisting of one cable or cord fitted with one plug connector and one connector, intended for the interconnection between two electrical appliances". Connector: "part of the appliance coupler integral with, or intended to be attached to, one cord connected to the supply".

Please note:

Category 7a cable was likely originally introduced as a future-proofing step for the anticipated wider uptake of a 40 Gbps Ethernet standard - however, in 2016 a new ratification meant that this responsibility was effectively handed over to Cat8 cables specified to 2000 MHz. As a result, cable Cat7a as a standalone revision isn’t officially supported by very much equipment to run at significantly faster speeds than Cat7 versions, although speed boosts may be possible in certain applications. Some electric kettles and similar hot household appliances like home stills use a supply cord with a C15 connector and a matching C16 inlet on the appliance; their temperature rating is 120°C (248°F) rather than the 70°C (158°F) of the similar C13/C14 combination. The official designation in Europe for the C15/C16 coupler is a "hot-condition" coupler.

A C8B inlet type is defined by the standard for use by dual-voltage appliances; it has three pins and can hold a C7 connector in either of two positions, allowing the user to select voltage by choosing the position the connector is inserted. [22] Australian/New Zealand Standard AS/NZS 60320.1:2004, Appliance couplers for household and similar general purposes Part 1: General Requirements (IEC 60320-1, Ed. 2.0 (2001) MOD). This is the Australian version of the IEC standard with national variations shown.

Appliances can be used in another country easily, with a simple change of the power supply cord (including a connector and a country-specific plug). The power supply cord can be replaced easily if damaged, because it is a standardized part that can be unplugged and re-inserted. Safety hazards, maintenance expenditure and repairs are minimized. Appliance inlet: "part of the appliance coupler integrated as a part of an appliance or incorporated as a separate part in the appliance or equipment or intended to be fixed to it". IEC 60320-3: Standard sheets and gauges. [4] First published October 31, 2014, this part initially included the standard sheets for both appliance couplers and interconnection couplers. In a 2018 amendment, the standard sheets for the IP couplers defined by 60320-2-3 were added. [9] For appliance couplers the various coupler outlines are designated using a combination of letters and numbers, e.g., "C14". The connector supplies power to the appliance inlet. The appliance inlet is designated by the even number one greater than the number assigned to the connector, so a C1 connector mates with a C2 inlet, and a C15A mates with a C16A. Interconnection couplers have single letter designators, e.g., "F". They consist of a plug connector and an appliance outlet. The plug connector is the part integral with, or intended to be attached to, the cord, and the appliance outlet is the part integrated with or incorporated into the appliance or equipment or intended to be fixed to it, and from which the supply is obtained. Standard sheet C25 shows retaining device dimensions. Sheet C26 shows detail dimensions for pillar-type terminals, where the end of the screw bears on a wire directly or through a pressure plate. Sheet 27 shows details for screw terminals, where the wire is held by wrapping it around the head of a screw. The PlayStation 5 has an inbuilt HDMI 2.1 port located at the console’s rear. That should tell you that it supports using an HDMI cable because of its advanced screen resolution capacities. Gaming on the PS5 with an HDMI cable connection gives you an optimal experience.

In addition to the connections within the standards, as mentioned, there are possible combinations between appliance couplers and IEC interconnection couplers. Fitted with a flexible cord, the components become interconnection cords to be used for connecting appliances or for extending other interconnection cords or power supply cords. The Cat 7 cable is similar in physical makeup to the previous Cat6 cable. Both versions use the same twisted and sheathed four-pair cable design as each other, capable of delivering transmission frequencies (bandwidth) of up to 600 MHz, and therefore both support 10 Gbps Ethernet signals over distances of up to 100m.These cables are sometimes informally referred to as a "kettle cord" or "kettle lead", but the C13/14 connectors are only rated for 70°C (158°F): a device such as a kettle requires the C15/16 connector, rated for 120°C (248°F). This kind of coupler is used by Roland Corporation for a couple of synthesizer and drum-computer models (for example: TR-909, D-50) and by Revox for many older models of their hi-fi equipment (for example, A76, A77, A78, B77, B225). Was also used heavily on Marantz hi-fi equipment in the 1980s and 1990s. For use in very-high-temperature settings, such as some stage lighting instruments. Similar to C15/C16, but the top is narrowed to exclude the C15 cord connector. The first edition of IEC 320 was published in 1970 [2] and was renumbered to 60320 in 1994. [3] Terminology [ edit ] IEC 60320 C5 connector